사용자 설명서 HITACHI CP-X807W

[. . . ] The best display performance will be achieved if the resolutions of the input signal and projector panel are identical. · Automatic adjustment may not function correctly with some input signals. · The image may not be displayed correctly when the input sync signal is a composite sync or a sync on G. · The HDMI input does not support the signals marked with *. 1 Initial set signals Initial set signals The following signals are used for the initial settings. [. . . ] Click the [Enable] check box to open [Network Control Port2 (Port: 9715)] to use TCP #9715. Click the [Enable] check box for the [Authentication] setting when authentication is required. Default setting is "Enable". Port open Network Control Port2 (Port: 9715) Authentication When the authentication setting is enabled, the following settings are required. Security Settings Authentication Password Network Control Re-enter Authentication Password Enter the desired authentication password. This setting will be the same for [Network Control Port1 (Port: 23)] and [Network Control Port2 (Port: 9715)]. Default setting is blank. 9 Command Control via the Network (continued) Command Format [TCP #23] 1. Protocol Consist of header (7 bytes) + command data (6 bytes) 2. Header BE + EF + 03 + 06 + 00 + CRC_low + CRC_high 3. Command data Command data chart byte_0 byte_1 byte_2 byte_3 byte_4 byte_5 Action Type Setting code low high low high low high Action (byte_0 - 1) Action Content 1 Set Change setting to desired value. 2 Get Read projector internal setup value. 6 Execute Run a command. Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data (`02H' + `00H' + type (2 bytes) + `00H' + `00H') (2) The projector returns the response code `1DH' + data (2 bytes) to the PC. Changing the projector settings (Set command) (1) Send the following setting code from the PC to the projector. Header + Command data (`01H' + `00H' + type (2 bytes) + setting code (2 bytes)) (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code `06H' to the PC. Using the projector default settings (Reset Command) (1) The PC sends the following default setting code to the projector. Header + Command data (`06H' + `00H' + type (2 bytes) + `00H' + `00H') (3) The projector returns the response code `06H' to the PC. Increasing the projector setting value (Increment command) (1) The PC sends the following increment code to the projector. Header + Command data (`04H' + `00H' + type (2 bytes) + `00H' + `00H') (2) The projector increases the setting value on the above setting code. (3) The projector returns the response code `06H' to the PC. 10 Command Control via the Network (continued) Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data (`05H' + `00H' + type (2 bytes) + `00H' + `00H') (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code `06H' to the PC. When the projector cannot understand the received command When the projector cannot understand the received command, the error code `15H' is sent back to the PC. [. . . ] HIGH LANGUAGE Set Operation Type Off On Get Off On Get Off On Get Off On Get Off On Get ENGLISH FRANÇAIS DEUTSCH ESPAÑOL ITALIANO NORSK NEDERLANDS PORTUGUÊS BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF Header 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Command Data Type Setting Code 00 26 00 26 00 26 02 26 02 26 02 26 01 26 01 26 01 26 30 26 30 26 30 26 31 26 31 26 31 26 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 05 30 15 30 15 30 15 30 43 70 16 30 16 30 16 30 44 70 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 02 00 03 00 04 00 05 00 06 00 07 00 08 00 09 00 10 00 0A 00 0B 00 0C 00 0D 00 0E 00 0F 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 CRC FF 32 6F 33 CC 32 47 33 D7 32 74 33 03 33 93 32 30 33 FF 3D 6F 3C CC 3D 03 3C 93 3D 30 3C F7 D3 67 D2 97 D2 07 D3 37 D1 A7 D0 57 D0 C7 D1 37 D4 A7 D5 37 DE 57 D5 C7 D4 F7 D6 67 D7 97 D7 07 D6 C4 D3 04 D7 62 D7 B3 D6 DC C6 40 D7 26 D7 F7 D6 A8 C7 Action 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 02 00 02 00 04 00 05 00 06 00 02 00 04 00 05 00 06 00 Set Set Set Set Set SVENSKA SUOMI POLSKI TÜRKÇE Get Get Increment Decrement Execute Get Increment Decrement Execute MENU POSITION H MENU POSITION H Reset MENU POSITION V BE EF BE EF BE EF BE EF BE EF 06 00 06 00 06 00 06 00 06 00 MENU POSITION V Reset 22 RS-232C Communication / Network command table (continued) Names BLANK Set Operation Type My Screen ORIGINAL BLUE WHITE BLACK Get BLANK On/Off Set TURN OFF TURN ON Get START UP Set My Screen ORIGINAL TURN OFF Get My Screen LOCK Set TURN OFF TURN ON Get MESSAGE Set TURN OFF TURN ON Get AUTO SEARCH Set TURN OFF TURN ON Get AUTO OFF Get Increment Decrement AUTO ON Set TURN OFF TURN ON Get LAMP TIME LAMP TIME Reset FILTER TIME FILER TIME Reset Get Execute Get Execute BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF Header 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 Command Data Type Setting Code 00 30 00 30 00 30 00 30 00 30 00 30 20 30 20 30 20 30 04 30 04 30 04 30 04 30 C0 30 C0 30 C0 30 17 30 17 30 17 30 16 20 16 20 16 20 10 31 10 31 10 31 20 31 20 31 20 31 90 10 30 70 A0 10 40 70 20 00 40 00 03 00 05 00 06 00 00 00 00 00 01 00 00 00 20 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00 CRC FB CA FB E2 CB D3 6B D0 9B D0 08 D3 FB D8 6B D9 C8 D8 CB CB 0B D2 9B D3 38 D2 3B EF AB EE 08 EF 8F D6 1F D7 BC D6 B6 D6 26 D7 85 D6 08 86 6E 86 BF 87 3B 89 AB 88 08 89 C2 FF 58 DC C2 F0 98 C6 Action 01 00 01 00 01 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 02 00 01 00 01 00 02 00 02 00 04 00 05 00 01 00 01 00 02 00 02 00 06 00 02 00 06 00 23 RS-232C Communication / Network command table (continued) Names MY BUTTON-1 Set Operation Type RGB1 RGB2 HDMI COMPONENT S-VIDEO VIDEO MIU INFORMATION AUTO KEYSTONE V MY MEMORY PICTURE MODE FILTER RESET ACTIVE IRIS e-SHOT VOLUME + VOLUME AV MUTE LIVE MODE THUMBNAIL SLIDE SHOW DIRECTORY REMOVE MEDIA Get MY BUTTON-2 Set RGB1 RGB2 HDMI COMPONENT S-VIDEO VIDEO MIU INFORMATION AUTO KEYSTONE V MY MEMORY PICTURE MODE FILTER RESET ACTIVE IRIS e-SHOT VOLUME + VOLUME AV MUTE LIVE MODE THUMBNAIL SLIDE SHOW DIRECTORY REMOVE MEDIA Get BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE BE BE BE BE BE BE BE BE BE BE BE BE BE BE EF EF EF EF EF EF EF EF EF EF EF EF EF EF EF Header 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 06 06 06 06 06 06 06 06 06 06 06 06 06 06 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Command Data Type Setting Code 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 00 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 01 36 00 00 04 00 03 00 05 00 02 00 01 00 06 00 10 00 11 00 12 00 13 00 14 00 15 00 16 00 17 00 18 00 19 00 20 00 21 00 22 00 23 00 24 00 00 00 00 00 04 00 03 00 05 00 02 00 01 00 06 00 10 00 11 00 12 00 13 00 14 00 15 00 16 00 17 00 18 00 19 00 20 00 21 00 22 00 23 00 24 00 00 00 CRC 3A 33 FA 31 CA 33 6A 30 5A 32 AA 32 9A 30 FA 3E 6A 3F 9A 3F 0A 3E 3A 3C AA 3D 5A 3D CA 3C 3A 39 AA 38 FA 2A 6A 2B 9A 2B 0A 2A 3A 28 09 33 C6 32 06 30 36 32 96 31 A6 33 56 33 66 31 06 3F 96 66 F6 C6 56 A6 36 C6 56 06 96 66 F6 C6 F5 3E 3E 3F 3D 3C 3C 3D 38 39 2B 2A 2A 2B 29 32 Action 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 02 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 01 00 02 00 24 RS-232C Communication / Network command table (continued) Names MAGNIFY Operation Type Get Increment Decrement FREEZE Set NORMAL FREEZE Get e-SHOT Set OFF IMAGE 1 IMAGE 2 IMAGE 3 IMAGE 4 Get e-SHOT IMAGE1 Delete e-SHOT IMAGE2 Delete e-SHOT IMAGE3 Delete e-SHOT IMAGE4 Delete Execute Execute Execute Execute BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF BE EF Header 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 03 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 06 00 Command Data Type Setting Code 07 30 07 30 07 30 02 30 02 30 02 30 00 35 00 35 00 35 00 35 00 35 00 35 01 35 02 35 03 35 04 35 00 00 00 00 00 00 00 00 01 00 00 00 00 00 01 00 02 00 03 00 04 00 00 00 00 00 00 00 00 00 00 00 CRC 7C D2 1A D2 CB D3 83 D2 13 D3 B0 D2 3A C3 AA C2 5A C2 CA C3 FA C1 09 C3 71 C3 35 C3 C9 C2 BD C3 Action 02 00 04 00 05 00 01 00 01 00 02 00 01 00 01 00 01 00 01 00 01 00 02 00 06 00 06 00 06 00 06 00 25 Hitachi, Ltd. Japan 292 Yoshida-cho Totsuka-ku, Yokohama-city Kanagawa 244-0817 HITACHI EUROPE LTD. Consumer Affairs Department PO Box 3007 Maidenhead SL6 8ZE UNITED KINGDOM Tel: 0870 405 4405 Email: consumer. mail@Hitachi-eu. com HITACHI EUROPE GmbH Munich Office Dornacher Strasse 3 D-85622 Feldkirchen bei München GERMANY Tel: +49 -89-991 80-0 Fax: +49 - 89 - 991 80 -224 Hotline: +49 - 180 - 551 25 51 (12ct/min. ) Email: HSE-DUS. Service@Hitachi-eu. com HITACHI EUROPE SRL Via T. Gulli n. 39 20147 MILAN ITALY Tel: 02 487861 Fax: 02 48786381 Servizio Clienti Tel. [. . . ]