사용자 설명서 BRAUN 760 CC

[. . . ] Do not expose to direct sunlight for long periods of time. Do not refill the cartridge and use only original Braun refill cartridges. STOP Description Clean&Renew station 1 Cleaning fluid display 2 Lift button for cartridge exchange 3 Station-to-shaver contacts 4 «clean & dry» button 5 Cleaning program indicators 6 Station power socket 7 Cleaning cartridge Shaver 8 Foil & Cutter cassette 9 Cassette release button 0 Shaver head «lock» switch q Pop-out long hair trimmer 10 w e r t z u i o p On/off switch «sensitive» (­) setting button «intensive» (+) setting button Reset button Shaver display Shaver-to-station contacts Shaver power socket Travel case Special cord set Before shaving Prior to first use you must connect the shaver to an electrical outlet using the special cord set p or alternatively proceed as below. Installing the Clean&Renew station · Using the special cord set p, connect the station power socket 6 to an electrical outlet. cle clean an & dry clean high low empty · Press the lift button 2 to open the housing. 2 fast clean 1 new · Hold the cleaning cartridge 7 down on a flat, stable surface (e. g. [. . . ] Charging information · A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth. 07 00 75 charge lo 25 w 12 5 50 1 07 00 75 50 · The best environmental temperature for charging is between 5 °C to 35 °C. Do not expose the shaver to temperatures higher than 50 °C for extended periods of time. Personalizing your shaver Personalizing your shaver With the «sensitive» e and «intensive» r buttons you can choose the best setting for shaving different areas of your face and as per your specific needs. The different settings are indicated by the pilot light incorporated in the on/off switch w: intensive on normal on sensitive on · «Intensive» = dark blue (powerful shave) · «Normal» nsive = light blue off off sitive sitive nsive nsive sitive off · «Sensitive» = white (for a thorough comfortable shave in sensitive areas of your face such as neck) For a thorough and fast shave we recommend the «intensive» setting. Pressing the « + » or « ­ » button activates your preferred setting. When switching on next time, the last used setting will be activated. How to use Press the on/off switch w to operate the shaver: · The pivoting shaver head and floating foils automatically adjust to every contour of your face. · To shave hard to reach areas (e. g. under the nose) slide the shaver head «lock» switch 0 to the back position to lock the pivoting head at an angle. · To trim sideburns, moustache or beard, slide the pop-out long hair trimmer upwards. trimmer off on tr sensitive intensive reset 1 loc k 2 lock lo ck lock off Tips for the perfect shave For best shaving results, Braun recommends you follow 3 simple steps: 1. At all times, hold the shaver at right angles (90°) to your skin. Stretch your skin and shave against the direction of your beard growth. on release 13 Shaving with the cord If the shaver has run out of power (discharged), and you do not have the time to recharge it in the Clean&Renew station, you may also shave with the shaver connected to an electrical outlet via the special cord set. Cleaning Automatic cleaning After each shave, return the shaver to the Clean&Renew station and proceed as described above in the section «Before shaving». All charging and cleaning needs are then automatically taken care of. With daily use, a cleaning cartridge should be sufficient for about 30 cleaning cycles. [. . . ] Then the shaver will automatically reset the display. After you have replaced the Foil & Cutter cassette, use a ball-pen to push the reset button t for at least 3 seconds to reset the counter. While doing so, the replacement light blinks and goes off when the reset is complete. [. . . ]