사용자 설명서 ZANUSSI ZGF96XK

[. . . ] 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Disconnect the appliance from the electrical supply, before carrying out any cleaning or manteinance work. Ensure a good ventilation around the appliance. A poor air supply could cause lack of oxygen. Ensure that the gas supply complies with the gas type stated on the identification label, placed near the gas supply pipe. This appliance is not connected to a combustion products evacuation device. It must be installed and connected in accordance with current installation regulations. Particular attention shall be given to the relevant requirements regarding ventilation. The use of a gas cooking appliance results in the production of heat and moisture in the room in which it is installed. Ensure that the kitchen is well ventilated: keep natural ventilation holes open or install a mechanical ventilation device (mechanical extractor hood). Prolonged intensive use of the appliance may call for additional ventilation, for example opening of a window, or more effective ventilation, for example increasing the level of mechanical ventilation where present. The manufacturer disclaims any responsability should all the safety measures not be carried out. injury or serious malfunctioning. - For other hobs use Hob Brite or Bar Keepers Friend. Do not leave acid or alkaline substances (e. g. vinegar, salt, lemon juice, etc. ) on the cooktop. The Ignition electrode The electric ignition is obtained through a ceramic electrode with a metal electrode inside. Keep these components very clean, to avoid difficult lighting, and check that the burner crown holes are not obstructed. 31 Technical data Cut out dimensions (see chapter "Building In") Width: Depth: 560 mm 480 mm 594 mm 510 mm Heat Input Rapid burner Semi-rapid burner Auxiliary burner Natural gas3, 0 kW Liquid gas 2, 8 kW 2, 0 kW 1, 0 kW Overall dimensions Width: Depth: Electric supply: 220 V ~ 60 Hz Category: II2H3+ Gas supply: natural gas G20 (2H)/ 20 mbar Appliance class 3 Gas burners BURNER NORMAL POWER kW REDUCED POWER kW NORMAL POWER NATURAL POWER m3/h inj. 100/mm LPG 28-30/37 mbar g/h inj. 100/mm G20 20 mbar G30 G31 Auxiliary 1, 0 0, 33 70 0, 095 50 73 71 Semi-rapid 2, 0 0, 45 96 0, 190 71 145 143 Rapid Natural gas : 3, 0 Liquid gas: 2, 8 0, 75 130 0, 286 86 204 200 By-pass diameters Burner Ø By-pass in 1/100 mm. Auxiliary Semi-rapid Rapid 28 32 42 32 Installation The following instructions about installation and maintenance must be carried out by qualified personnel in compliance with the regulation in force. The side walls of the unit in which the hob is going to be installed, must not exceed the height of the working top. Avoid installing the appliance in the proximity of inflammable materials (e. g. The appliance must be electrically disconnected before all interventions. If any electric supply to the appliance is required to carry out the work, ensure all the necessary precautions are followed. THE MANUFACTURER WILL NOT ACCEPT LIABILITY, SHOULD ANY OF THE OTHER SAFETY INSTRUCTIONS INCORPORATED IN THIS BOOK OR THE REGULATION IN FORCE BE IGNORED. The adjustable connection is fixed to the comprehensive ramp by means of a threaded nut G 1/2". Interpose the sealing between the components as shown in the picture. [. . . ] If there are side walls, or sides of the furniture unit near the hob, the cut out edges must have a minimum distance of 100 mm. Hanging forniture units or hoods must be placed at 650 mm. Fitting the hob to the worktop Carry out the building in of the hob as follows: 1. Place the seals supplied with the hob on the front edge of the cut out. [. . . ]