사용자 설명서 PHILIPS FC9226

[. . . ] FC9239-FC9220 2 3 5 14 13 15 6 1 5 1 7 8 9 10 2 16 17 11 3 4 18 19 12 20 21 22 25 24 23 26 30 27 28 29 31 32 English 8 15 22 FC9239-FC9220 English general description (Fig. 1) 1 Filtercylinder 2 Filtercylindercase 3 Dustbucketreleasebutton 4 Dustbucket 5 Hoseconnectionopening 6 Suctionpowerbuttons(MINandMAX) 7 Suctionpowerlights 8 Filter-Cleanbutton 9 On/offbutton 10 Cover 11 MotorProtectionFilter 12 Wheel 13 Cordrewindbutton 14 Hoseconnector 15 Hosereleasebutton 16 Remotecontrol(specifictypesonly) 17 Handgrip 18 Accessoryholder 19 Telescopictube 20 Smallbrush 21 Smallnozzle 22 Crevicetool 23 Tri-Activenozzle 24 Sidebrush 25 Parking/storageridge 26 SuperCleanAirHEPAFilterorUltraCleanAirHEPAFilter 27 Filtergrille 28 Mainscord 29 Parkingslot 30 Swivelwheel 31 Storageslot 32 Typeplate important Readtheseinstructionsforusecarefullybeforeusingtheapplianceandsavethemforfuture reference. , Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance. , Do not use the appliance if the plug, the cord or the appliance itself is damaged. [. . . ] 20) , The light in the Filter-Clean button goes on and you hear a beep before the filter-cleaning process starts. English , , During the filter-cleaning process the appliance produces a rattling noise. When the filter-cleaning process is finished, you hear a beep and the light in the Filter-Clean button goes out. 9 You can also press the Filter-Clean button during vacuum cleaning. , When you do this, the motor stops running and the filter cleaning-process starts. During the filter-cleaning process, the appliance does not suck up dirt. When the filter-cleaning process is finished, the motor automatically starts running again and you can continue vacuum cleaning. , If you fail to press the Filter-Clean button after vacuuming several times, the light in the Filter-Clean button starts blinking. This tells you that you need to press the Filter-Clean button to prevent the filter from becoming clogged. , The light stops blinking after you have cleaned the filter by pressing the Filter-Clean button. Cleaning and maintenance Always press the Filter-Clean button when you have finished vacuum cleaning. Cleaning the dust bucket and filter cylinder case Always unplug the appliance before you empty the dust bucket. The dust bucket is not dishwasher-proof. 1 Empty the dust bucket as soon as the dust level has reached the round disc of the filter cylinder case. 21) 2 Switch off the appliance, remove the mains plug from the wall socket and disconnect the hose from the appliance. 3 Unlock the cover by pressing the release button on top of the handle of the dust bucket (1). 22) Remove the dust bucket by lifting it out of the appliance. 23) 5 Hold the dust bucket over a dustbin and lift the filter cylinder case out of the bucket. 24) Gently tap the filter cylinder case against the dustbin to release all fine dust from the case. 25) 7 If you want to clean the filter cylinder case more thoroughly, first remove the filter cylinder from the case. To remove the filter cylinder, turn the handle on top of the filter cylinder anticlockwise (1) and lift the filter cylinder out of the case (2). 26) 8 Then clean the filter cylinder case with a dry cloth or with cold tap water and some washingup liquid. 27) , Do not clean the filter cylinder case with the filter cylinder in it under the tap. 28) 9 Put the filter cylinder back into the filter cylinder case. [. . . ] 2 The appliance cannot be switched on and the suction power lights blink. , The filter cylinder case with the filter cylinder in it has not been inserted into the dust bucket. Insert the filter cylinder case with the filter cylinder. 3 , , , , The suction power is insufficient. [. . . ]